La conținutul paginii

Microphone Preamplifier

  • Extremely low-noise Class A JFet amplifier
  • For dynamic and ribbon microphones
  • 2 Matched JFet transistor pairs
  • Input: Balanced 3-pin XLR female
  • Output: Balanced 3-pol. XLR male
  • Input impedance: 20 kOhm
  • Gain: 28 dB (@ 3 kOhm source impedance)
  • Frequency response: 10 - 50,000 Hz (+/- 1 dB)
  • Requires phantom power: 24 - 48 V.
  • Dimensions (L x W): 77 x 22 mm
  • Weight: 35 g
  • Developed and produced in Germany

Note: Does not allow phantom power to pass through to the microphone

  • disponibil din August 2020
  • numărul articolului 495774
  • unitate de vânzare 1 bucată(ăţi)
  • Channels 1
  • Number of microphone inputs 1
  • Instrument input No
  • Tubes No
  • Compressor/Limiter No
  • Equalizer No
  • De-Esser No
  • Phantom power No
  • Phase Reverse No
  • External effect loops No
  • Analogue Outputs XLR
  • Digitale Outputs 0
  • Headphone connection No
  • Level Meter No
  • Design Adaptor
259 lei
Toate prețurile includ TVA
în stoc
1

295 Evaluările clienților

4.5 / 5

Manipulare

Caracteristici

Sunet

Măiestrie

188 Recenzii

ll
Nu a functionat
le loo 05.07.2024
Nu stiu ce face l am primit cadou de la thomann dar nu a functionat la nimic..
Am zis ca l tin pt ca e cadou si nu as trimite inapoi la service pt ca oricum e gratuit deci asta e
Manipulare
Caracteristici
Sunet
Măiestrie
0
0
semnaleaza un abuz

semnaleaza un abuz

google translate gb
Din păcate a intervenit o eroare. Vă rugăm încercați din nou mai târziu.
E
Excellent silent pre-amp
EdEditz 19.08.2022
Whenever I buy a Ribbon mic, I always get one of these with it because it makes a world of difference in the sound level and therefor the noise floor. You can also use them with dynamic mics to really boost the level. This one is very transparent and won't color the sound.
Manipulare
Caracteristici
Sunet
Măiestrie
5
0
semnaleaza un abuz

semnaleaza un abuz

google translate gb
Din păcate a intervenit o eroare. Vă rugăm încercați din nou mai târziu.
B
So simple and yet so effective
BRandySavage 24.02.2022
I bought this little guy to pair alongside a Rode Podmic. I have tested the mic both with and without the FetAmp. This tiny piece works wonders and really amplifies the sound of the Podmic allowing me to use the Mic with my Mixer with little to no gain at all. Does exactly what it says it does.
Manipulare
Caracteristici
Sunet
Măiestrie
4
0
semnaleaza un abuz

semnaleaza un abuz

google translate gb
Din păcate a intervenit o eroare. Vă rugăm încercați din nou mai târziu.
T
Worth getting for Dynamic mics
TDawg93 27.03.2025
I bought this to accompany the t.bone BC500, and it’s so worth it for a few reasons:
(1) increased gain = decreased noise. It adds a fair load of gain (without clipping) to dynamic mics, resulting in not needing to crank the gain knob, meaning there’s a much lower amount of noise in your signal,
(2) it adds a touch of colour to the sound, barely noticeable but a nice addition to the BC500,
(3) it’s a really great price for what it’s doing!

There are only really two slight drawbacks with this:
(1) the length means it kind of ‘sticks out’ whether you have it on the Interface end or Mic end, making it look messier and messing up your cable management a tiny bit,
(2) the weight means it doesn’t work amazingly to have it on the mic end of the BC500, as the stand isn’t strong enough to hold the angle with the weight of this sticking out of the back of your mic.

However, I’m so glad I bought this - even just the increased gain element is enough to make this worth having despite the very mild drawbacks!
Manipulare
Caracteristici
Sunet
Măiestrie
2
0
semnaleaza un abuz

semnaleaza un abuz